login   |    register

Built Review
Polish Winged Hussar

by: Ray [ RAYW ]

Originally published on:
Historicus Forma

This kit, from Alpha Image, has been available for quite awhile. It is the only 120mm Winged Hussar that I know of, and as a modeler with a fascination for cavalry it was a must have. I must say I was not too disappointed.

What’s Inside
The kit comes well stocked for a full build. A brass rod and copper foil is provided for the lance and flag. A small chain is also provided for the mouth bit. The kit components are well sculpted and well cast. The sheer number of components is a little intimidating to the modeler who may be accustomed to simpler figures. A color picture is also provided for reference.

I treated this kit like several smaller, individual kits. I approached it like I was building a vignette and not a single figure.

The Horse
This is one of the best sculpted horses I have seen in awhile. The pose is very animated and it went together well. The horse halves were off a bit and had a slight gap. This was easily fixed with a little Milliput and a wet brush. The neck/head piece had a slight gap as well which I fixed in a similar fashion. The ears were broken on my particular kit so I sculpted new ones with my trusty Milliput.

Once the horse was assembled, it was time to paint. Here is where I ran into the most frustrating thing with this model. I couldn't get any primer or paint to adhere to the model! I washed it with soap and water, I lightly sanded it and still no joy. My suspicion was there was a mold release agent present that was my bane. I first primed with Warhammer white primer. It dried then flaked off. I airbrushed Humbrol enamels with the same result. I tried brush painting acrylics and the paint just pooled off. It was very frustrating. Imagine, I had this beautiful figure and I couldn't paint it! It got to the point where I put the kit away for several years. A fellow modeler suggested I use auto primer. I tried it and lo and behold it stuck!! I was back in business! I then proceeded to paint the horse a dapple grey. I will be submitting a full article on painting horses a little later so I won't go into detail on how it was painted.

Once I finished the horse I put it aside. I found the casting for the mouth bit too brittle to clean up and take off the mold so I replaced it with a wire bit that I made myself.

The Rider
Like the horse, the rider was well sculpted. The expression on the face was nicely animated and a pleasure to paint. There was a slightly larger gap for the right arm which again I fixed with Milliput. The hands seemed a little small for the figure but not to the point where they looked totally out of place. The head fit very well to the torso. I had the same problem with painting as I had with the horse but my favorite new primer took care of that. The rider was a straight forward build with no real issues. The spurs, like the horse bit, were too small and brittle to use so I replaced them with ones I made from sprue and wire, using the kit piece as a master.

The Wings
Each wing is comprised of 48 or so individual feathers. I took each off the sprue, cleaned the flash off, and painted them. Once each feather was completed I attached them to the back braces. Once dry I attached the wings to the figure.

As I mentioned earlier, the kit comes with a brass rod and copper foil for the lance and flag. I quickly realized that it was too heavy for the figure and wouldn't balance right. In hindsight I should have realized this and should have drilled a hole through the hand for better attachment. I also removed the small connector rod on the lance and drilled a deep hole. I made a wooden dowel from a toothpick and connected it to the lance. I then used this to connect to the hand to give it some stability. It worked and the lance balanced out. I then attached the figure to the horse and it all fit together very well.

Once completed, I must say I felt very pleased with my Polish Winged Hussar and am proud to have it on my shelf. The only real issue was the mold release agent. This may frustrate many a modeler, especially after spending $140 US which is not in everybody's budget.

After all is said and done though, I look at my Hussar in my den and say "What the heck", and am glad it is there :)

If you’re a 120mm Cavalry nut like me then you will be pleased with this kit. It is a very advanced kit and once started be prepared for a stimulating build to say the least. Kudos goes to Alpha Image Model Workshop for providing us with this beautiful kit.
The kit is a very nice build. Because of the many parts involved with this figure, I would suggest it for advanced modelers. The issue with the inability for primer and paint to adhere to the resin was very frustrating and I suspect my kit had a mold release agent.
Percentage Rating
  Scale: 120mm
  Mfg. ID: W12006
  Suggested Retail: $140.00 US
  Related Link: Alpha Image Model Workshop
  PUBLISHED: May 04, 2005

About Ray (RayW)

Mainly into figure modelling but sometimes branches off into armour and aircraft. I would like to do more Sci Fi Fantasy figures and maybe will start that someday. My primary interests are Military History, dog sledding

Copyright ©2020 text by Ray [ RAYW ]. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of AeroScale. All rights reserved.


What's Your Opinion?

Click image to enlarge
  • 120mmmountedproductmenu
  • hussar1
  • hussar2
  • hussar3
  • hussar4