LOON MODELS [ MORE REVIEWS ] [ WEBSITE ] [ NEW STORIES ]

In-Box Review
132
Siemens-Schuckert D.III Late
  • move

by: tripping the rift [ THEGIRL ]

Brief History
In 1847 Siemens Halske started out manufacturing telegraphic equipment and in 1873 the Siemens-Schuckert title was founded by merging with Nurnberg Schuckert. 1907 and the firm moved into aeronautical work with the construction of non-rigid airships.

Between 1907 and 1911, three monoplanes were built, but aircraft manufacturing ceased until 1914 when German Military officials were in need of more aircraft. The aircraft department was reopened, directed by Dr. Walter Reichel, Dr. Hugo Natalis, Messrs Forssman, Wolff and the Steffen brothers - Bruno and Franz whose roles were leading assistants.

In 1916 several captured French Nieuport aircraft were readily available to Albatros , Euler and SSW. Siemens made a copy with a few difference to the engine, landing struts, prop and spinner, and the tailskid. This aircraft was designated the SSW D.I. In November 1916 production was cancelled due to superior aircraft by German and Allied manufacturers. Trials continued with the SSW D.II /a/b/c leading to the development of the D.III.

On Jan. 20, 1918 the D.III was entered into fighter competitions with aircraft going to the front for evaluation. The aircraft suffered numerous engine failures due to the use of the wrong type of oil (Low viscosity oil mislabeled at the factory) which played havoc on the engines, causing them to seize and disintegrate in flight.

These initial airframes assigned to JG II were sent back to the factory for refits and recommended modifications. These included altering the cowl by cutting out the lower half and adding a vented spinner. The control surfaces were also changed; the rudder was given a larger area, the elevator area was also enlarged, and balances added to the ailerons.

Note: Not all aircraft were retrofitted in the same way and one needs to check references to see which changes were made and not for your specific build.

The conversion set
Loon Models’ late conversion comes with the following parts:

2 x cowlings - 1 straight cut , 1 curved lower edge
1 x tail plane
1 x un-vented spinner
1 x front engine mount with 6 supports (two are spares)

The parts do have some flash which needs very careful clean up on the motor cowlings. These parts are really thin and bend easily. The straight cut cowl has see through spots, and if you’re not careful when sanding, you will go right though the resin leaving a nasty hole to fix. My sample does have some fit issues. The both motor cowls are undersize by 2mm and do not fit on Roden’s part 20a. Clean-up and test fitting will need care and attention in this area.

The horizontal tail surfaces have finely raised ribs for the elevator with hinge detail as well. Overall fit is nice, but it is also too short by a few millimeters, resulting in the rear fuselage overlapping the elevator. Here, plugging and filling will require care for a neat job and a lot of test fitting.

The spinner fits perfectly on the backing plate, the engine front mounting is nicely detailed with the supports (it’s very nice to have two extra in case of accidents). For placement of these parts use the Roden cowl / instructions as a guide .

Conclusion
Overall, I'm impressed with this conversion set. One has many options for a variety of late model D.III configurations. With some care working with the parts one shouldn’t have too many troubles.

References used:
Windsock Datafile #29 - SSW D.III / DIV, 1991
Profile Publications #86 - The Siemens Schuckert D.III / D.IV, 1966
WW 1 Aero Journal articles from issues 109, 123 and 132 by Dick Bennet
Scale Aircraft Drawings Vol 1, #1 - pages 94 - 97.

Please remember, when contacting retailers or manufacturers, to mention that you saw their products highlighted here - on AEROSCALE.
SUMMARY
Highs: Good quality and well detailed resin and extra parts.
Lows: Fit problems with the cowlings.
Verdict: A good conversion set with options for a variety of late model D.III configurations. With some care working with the parts one shouldn’t have too many troubles.
  Scale: 1:32
  Mfg. ID: Lo32207
  PUBLISHED: Sep 23, 2010
  NATIONALITY: Germany
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 70.00%
  MAKER/PUBLISHER: 92.00%

Our Thanks to Loon Models!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View Vendor Homepage  |  More Reviews  

About tripping the rift (thegirl)
FROM: ALBERTA, CANADA

Copyright ©2021 text by tripping the rift [ THEGIRL ]. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of AeroScale. All rights reserved.



Comments

Thanks Rowan for getting this one up so fast .
SEP 25, 2010 - 03:02 AM
Very good ! I am glad we caught these. Thank to Terri!
SEP 25, 2010 - 08:25 AM
Terri, What a wonderful review! Full of the info that I wanted to know about these parts. Thanks for showing the shortcomings and the good. Perfect. Dave
SEP 25, 2010 - 10:02 AM
Yes , it was a great catch on picking these items up , now I will have to get another Roden kit for back dating one
SEP 26, 2010 - 03:27 PM
no troubles at all Dave , glad you found the review helpful . I will be picking up another one , but this time the early conversion set .
SEP 26, 2010 - 03:28 PM
   
ADVERTISEMENT


Photos
Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
ADVERTISEMENT