EDUARD [ MORE REVIEWS ] [ WEBSITE ] [ NEW STORIES ]

In-Box Review
148
Supermarine Spitfire F Mk 22/24

by: Mal Mayfield [ HOLDFAST ]

Introduction.
The Supermarine SF Mk 24 Spitfire was the ultimate mark of this magnificent aeroplane, but was little changed from the F Mk 22 that preceded it. The lineage of these aircraft is easily recognisable, not least because of their magnificence, but they bare little resemblance to the earlier marks. They were over 100 mph faster than their earliest ancestors and possessed twice the rate of climb, even though they were almost double the empty weight of a Mk 1.

Content
The Eduard kit consists of the excellent Airfix kit plastic parts, an Aires resin cockpit, plus exhausts and F Mk 22 wheels. Eduard add one of their superb colour etch frets and canopy and wheel masks, excellent instruction booklet, colour marking guide and decals for four aircraft, 3 x F Mk 22s and 1 x F Mk 24.

The plastic parts.
The Airfix Spitfire F Mk 22/24 (and their Seafire FR 46/47) are, arguably, their best ever plastic kits. I have built the F Mk 22 previously and the kit is accurate in outline and size with correct panel lines (but more about this later). The fit is excellent, but there are a couple of areas that require some attention. Probably the worst part of the kit are the bulges over the Griffon engine rocker covers, they have a peculiar outline to the front end. I didn’t know about this when I built my F Mk 22, but if you have the SAM Publications Datafile on the Griffon powered Spitfire, you will see what is required to correct it. In fact it took me about 30 seconds to achieve the result here, which now just requires a little refining.

Although Airfix supply the Mk II Hispano (long) and Mk V Hispano (short) cannon barrels for the 2 marks, they only supply the wheels for the Mk 24 (3 spoke); again I wasn’t aware of this when I built my example. The control yoke, unfortunately, is moulded solid and is of the type found in the F Mk 22, but is wrong for the F Mk 24. The clear canopy parts are quite thin but there is distortion in the sliding part, which is also too small to sit on the rear fuselage in the open position. The clear parts are packed with the main sprues and my example is quite badly damaged. I checked the other Airfix kit that I have and that kit is packed the same way but the canopy isn’t so badly damaged. The cockpit makes up into a reasonable representation of the actual aircraft.

OK, so that’s the entire nit picking done. For my build of the F Mk 22 I used an Aeroclub vacformed canopy and scratch built the rollover pylon and head armour, to give a more scale appearance and I drilled out the control yoke. Refining the bulges over the rocker covers, as I have already said, is a doddle so the plastic is pretty good, it just needs a few tweaks.

The Aires resin parts.
These are produced in a medium grey resin and consist of all the parts necessary to build the cockpit, including, gyro gunsight, fuselage door and the F Mk24 control yoke. There are also 4 spoke wheels, as used on the F Mk 22 and hollowed out exhausts. All of these parts are of excellent quality with no air bubbles at all. The Eduard instructions show that the detail within the plastic fuselage halves must be removed, but there is no mention as to whether or not they require thinning down. However if you go onto the Eduard site there is a build of the kit which shows them thinned, which is, probably, what you would expect. As for all resin detail sets test fit and you won’t go wrong.

If you are building the F Mk24 do not open out resin part RP11, as this would be the front face of the rear fuselage fuel tank. The real trick with resin detail sets is in the painting; this set will give you a stunning cockpit, with a little work and a deft paintbrush.

The Eduard etched fret.
Well what’s to say? It’s Eduard and it’s coloured. You get the parts necessary to finish off the cockpit, such as the seat belts and instrument panels. The instrument panels are of Eduard’s superb painted dials and include the different “blind flying panels” for the different marks. The other internal parts consist of the rudder pedals and the roll over bar and head armour. So that’s another area of the kit that is addressed.

The rest of the etched parts are external and include gear leg torque links, radiator faces, and tail wheel door detail and cartridge case deflectors. Two other pieces are re-scribing templates, the smaller one is to scribe the door over the flap actuator, if you elect to not have the flaps lowered (I believe it to be highly unlikely to see a Spitfire parked with it’s flaps down). The fret includes these doors, if you do want to lower the flaps, but there is no internal detail given so you would have to scratch build this. The other template is to move the radio door, for the F Mk 22, on the starboard fuselage, but I have not been able to find definitive proof that the door was in a different place than that moulded. In the SAM Publications Datafile, however, there is a drawing showing the radio gear in 2 different positions. Forward, if the rear fuel tank was fitted and further to the rear if it was not. This might sound odd but it will be this way because of the centre of gravity. One of the differences of the F Mk24 is that it carried two 33 gallon fuel tanks in the rear fuselage, F Mk 22 did not. This being the case then the radio door on the F Mk 22 would, it seems, have been in the rear position, as Eduard indicates.

Instructions, marking guide, decals and paint masks.
The instructions are in Eduard’s usual clear style, the bonus being that those for the resin parts are far better than those you would have got if you had bought the Aires set separately. They correctly point out that only the F Mk24 was capable of carrying rockets, but suggest using the longer (Mk II) cannon barrels when the F Mk 24 had the shorter (Mk V) barrels. Which is one of the few externally different features of the F Mk24. Having said that, however, as the F Mk 24 was basically the F Mk 22 with a few minor changes, and 27 F Mk 22’s were converted to F Mk 24 standard, it is possible that some retained the longer barrels. Early production F Mk24s did have the longer barrels. Unfortunately I don’t have the references to identify which ones they might be. On the sprue guide the shorter barrels are indicated “not for use” but, from the information that I do have, 80 Squadron machines did have the short Mk V Hispano cannon barrels.

The marking guide is in colour and offers 4 different aircraft, only one of which is for the F Mk 24 - but only 80 Squadron flew the type. The Syrian example looks nice, in desert camo, and I already have the Aluminium doped 603 Squadron bird on my shelf (It is painted silver and is not natural metal, mores the pity). As I require an F Mk 24 alongside it, I’ll be doing the 80 Squadron machine. Eduard continues to be innovative, in that they have included a suggestion of staining on the colour profiles. A nice touch which could help those new to this type of weathering.

The decals look very good; the main markings are by Aviprint. They are in register and the detail on the Squadron badges is very good. The yellow outer ring on the 80 Squadron machine fuselage roundels looks a little pale - but application will tell. A nice touch is the codes, again for the 80 Squadron machine, which are applied over the black and white stripes and are coloured to suit, i.e. black on white, white on black, are separate. They are as one on the Airfix sheet but having them separate allows for painting on the stripes. All stencils are included, on a separate sheet, and are printed by Tally Ho!

The masks, for the wheels and canopy, are in the Tamiya tape type material and are a nice additional touch for those that like them. I don’t usually use these masking sets and they may not fit the vacformed canopy I have. I will try them, as they may prove useful.

Verdict and recommendations.
Superb, what more do you want? - the best Airfix kit, great Aires resin and Eduard’s colour etch, plus very well done decals and instructions - and it’s a Spitfire. It’s no wonder Eduard sold out so fast. Well obviously I’m going to recommend this kit; there are a couple of things to watch out for, but overall a great package and a bit of a bargain to boot. By way of comparison, I have the Cutting Edge resin cockpit, which is very good, but it alone cost me £15.95 a couple of years ago.

Thank you to Eduard for kindly supplying the review sample.

Please remember, when contacting retailers or manufacturers, to mention that you saw their products highlighted here - on Aeroscale
SUMMARY
There was huge excitement when Eduard announced that they were going to re-box the classic Airfix Spitfire F Mk 22/24 and add new resin and etched parts - so much so that the kit sold out on Eduard's website almost as soon as it was released.
  Scale: 1:48
  Mfg. ID: 1121
  Suggested Retail: £23.99
  PUBLISHED: Aug 19, 2006
  NATIONALITY: United Kingdom
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 86.75%
  MAKER/PUBLISHER: 88.59%

Our Thanks to Eduard!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View Vendor Homepage  |  More Reviews  

About Mal Mayfield (Holdfast)
FROM: ENGLAND - SOUTH WEST, UNITED KINGDOM

Hi, my name is Mal Mayfield and I have been modelling seriously for about 25 years. My main interest is 1/48 scale second world war. I build all types and all combatants. I have built 1/35 scale "targets" and 1/72 scale modern aircraft, plus a couple of cars. I have also dabbled with figure painting...

Copyright ©2021 text by Mal Mayfield [ HOLDFAST ]. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of AeroScale. All rights reserved.



Comments

Great review Mal on what must rank as one of the top Spitfire kits ever. Im SO glad I took the plunge and bagged one for myself!,and its mine,,,all mine,,,wooohaahaa,,,,,oops! The detail is just stunning, and its certainly worth following the link to Eduard website and checking out the build photos on there. Also a good opportunity for you to build a few more rockets after your article Mal Did the Eduard builder forget the arming cables? Did anyone decide if theres going to be a Group Build for this? I think Im going to open the box and have another drool over this right now Nige (who until this appeared only built 1:72 :-) )
AUG 19, 2006 - 02:23 AM
I will not be hanging any rockets on my Spitfire, what sacrilage Really I just love the lines of the F Mk 22/24 Spitfire, as I do all Spitfires Eduard have certainly put together an excellent package. Nige, you are going to need two of these kits, whichever Mk you build you will want to build the other, at some time You know what they say: "you just can't have too many Spitfires". I'm not entirely sure, I think a Spitfire build might be happening next year? However I am going to be starting an "on line" build of mine soon. I will do it via the forum, similar to the Fokker D.VII build, but I have to get hold of some Interior green paint first. I'm also in the process of changing my car, so this week end and possibly next week end are booked for things other than modelling. Mal
AUG 19, 2006 - 01:04 PM
I agree Mal.They just dont look right do they,,in the same way as Typhoon doesnt quite look right without them I am looking forward very much to your online build on this! It might be just a coincidence,but Hannants are showing the Squadron vacform canopy for the MK22/24 as out of stock.They had some last week.Looks like theyve sold out as quick as the kit I still cant stop opening the box and looking at the contents! Nige
AUG 20, 2006 - 04:43 PM
Thanks for the review Mal, especially the tips on correcting the few inaccuracies that exist. None of which are deal breakers for me. Very glad I snagged one of the last kits Spruebrothers had, and like lampie, I can't resist opening the box and drooling over the contents. I'll have to bag the decals to prevent water spots.
AUG 20, 2006 - 05:22 PM
Cool guys, mine is now permenantly open as I have started hacking resin. I will start the on line build as soon as I can take pics (Charging my camera battery as we speak), probably tomorrow. One thing that I can report on is that the resin is easy to work with as it is relatively soft and therefor not so brittle. I have managed to, slightly, damage the floor (you will see in the pics) but no major problem. Mal
AUG 20, 2006 - 11:24 PM
   
ADVERTISEMENT


Photos
Click image to enlarge
  • Ed_Spit22-24_Boxtop
  • Ed_Spit22-24_Contents
  • Ed_Spit22-24_Parts_1
  • Ed_Spit22-24_Parts_2
  • Ed_Spit22-24_Cowl_Blisters
  • Ed_Spit22-24_Resin_Parts
  • Ed_Spit22-24_Etch
  • Ed_Spit22-24_Instructions
  • Ed_Spit22-24_Decals
  • Ed_Spit22-24_Colours_1
  • Ed_Spit22-24_Colours_2
  • Ed_Spit22-24_Colours_3
  • Ed_Spit22-24_Colours_4
ADVERTISEMENT