ICM HOLDING [ MORE REVIEWS ] [ WEBSITE ] [ NEW STORIES ]

In-Box Review
148
Ju 88C-6b
Ju 88C-6b WW2 German Night Fighter
  • move

by: Darren Baker [ CMOT ]

Introduction

In the early 1930's Germany was looking for a twin engine bomber to outstrip the fighters in terms of speed. One of the aircraft designs resulting from this search was the Ju 88 designed and built by Junkers Flugzeug and Motorenwerke AG company.

In the spring of 1941 the Ju 88A-4 variant was produced with improved armament and powered by two liquid cooled Jumo 211J engines delivering better performance. In 1943 a night fighter variant of the Ju 88A-4 was produced with the title of Ju 88C-6b. this version was equipped with an MG FF cannon and 3 MG 17 machine guns in the nose, 2 MG FF cannons in the ventral gondola plus a further 2 MG FF cannons fitted in the fuselage at a fixed angle forward and upward; These last two were not fitted to all aircraft. As a night fighter variant of the Ju 88 the aircraft was fitted with either the FuG 202 or FuG 220 Radar. These aircraft saw service on both the Western and Eastern Fronts between 1943 and 1945.

ICM has continued to release a great selection of 1/48th scale aircraft and this time it is the Ju 88C-6b that is in their sites.

Review

This offering from ICM is packed in the now usual flip top cardboard box and a separate card lid, a great combination for protecting the contents. The only thing I would now change is the packing of the entire contents in a single plastic bag albeit the clear sprue being in its own bag within the main bag.

The moulding quality is good with no major flows observed by me. There are a few flow marks observable on the larger moulded elements, but my checks such as running my nail over them and looking at them under magnification would all indicate that this has not caused any issues. The obvious problem with all kits is the ever present ejector pin marks, these as you would expect have been hidden in areas not seen on the finished model, but a few will need to be addressed via filling and sanding. I will add here that with this being one of a number of Ju 88’s being released by ICM there are a number of parts not used with this model and so there are some significant spares. One thing I have found is that with this model example the engine nacelles are all distorted due to I believe the packing in a single bag place undue pressure on the parts.

The cockpit of the aircraft is the same as in previous releases, and I have to say I am rather pleased with what I see offered. The control panels are nicely replicated and would appear to be basically correct. The pilot’s instrument panel has been provided with decals by ICM, but if these do not please you I am sure Eduard or someone else will release an internal set for the model. A lot of attention has been lavished on the seats for the cockpit area, especially the support structures. The pilot’s seat has been moulded in two halves and this means there is a joint that needs to be hidden or filled; an aspect I would rather not be the case. The only real downside here that I can see is that no effort has been made to represent the crew’s harnesses; this is something I have become more picky about as I have progressed. Other than this I am very happy with this area of the model. Further on this aspect is that Eduard and maybe others have released generic harness sets that would be suitable for this model.

The rear wheel has been moulded as a single piece, it is well detailed from what I can ascertain, but it is something I do not like to see from a painting aspect. The front wheel units cheer me up quite a bit as I really like the detail moulded in this area of the model. The main struts look very good detail wise and the minor seams lines that need to be dealt with should be easy due to the breakdown of parts. The torsion links are supplied separately and so aid the clean up process. Just about everything other than the strut is supplied separately resulting in a very nice looking main undercarriage assembly. I especially like that these are assembled off of the model and added after assembly into what I believe will be a rigid structure. The tyres are well detailed, but they are not weighted which lets them down; I am sure that resin weighted wheels are or will be available soon for this model. The wheel bay doors have not been forgotten and are again very well detailed inside and out. The only thing the modeller really needs to add are the brake lines which are not moulded, but that is not exactly unusual.

The fuselage of the model has been tackled very well in order to make it reasonably easy for ICM to provide various versions of the Ju 88, but this has not been done in such a way as to make life difficult for the modeller. The radio direction finder has present and well detailed. The panel lines are very nicely recessed and fine, a check of drawings indicates that most of the panel lines appear to be present and correct. The large mouldings have an almost very lightly textured finish that I find appealing, but the parts are smooth; it is a hard sensation to explain. While covering the fuselage it is I believe a good time to look at the clear parts for the model. The clarity of the clear parts is very good and it would be worth looking for paint masks for this one, there are so many framed panels that you will need a very steady hand to avoid marring the finish. The thickness of the clear parts is fair, but there is a small amount of magnification that takes place. The defensive machine guns are reasonable detail wise and will look the part, but I would consider the metal barrel option as I think this model is worth the expense; at the very least take the time to drill out a short portion of the muzzles. An aspect that I like about how this model has been tackled from an assembly aspect is the lower portion of the fuselage under the wings; ICM has added a length of the wings that will make adding the rest of the wing portions so much easier for the modeller.

The vertical tail and rudder parts have the cut out in the top of the tail present, I do believe this is correct in most cases except for some very early Ju 88A-4’s. Panel lines throughout the flight surfaces are well represented and should look good when picked out. The rest of the flight surfaces are very well done and have the finish I spoke of earlier present. All of the flight control surfaces are supplied separately, and while not workable they do allow the modeller to decide the position they are set in.

Looking at the nacelles where there is quite a bit of distortion present on these parts, most likely due to the way they were packed, but due to the way everything goes together this issue should easily correct itself if the engine side panels are secured in place. There are two engines supplied by ICM and they do look to be very well detailed, but it is my understanding that there was a different engine in the A-4 as opposed to the A-5 and so one of the two models must be wrong as the engines are the same in all of the models; I suppose it would take someone with a very high degree of knowledge to pick out which engine it is exactly that is right or wrong. Regardless I am very pleased to see these in this model. Being engines it would pay to add some wiring to the area if you are going to display it. The cones and radiators are provided in this offering of the model. The propeller blades look very accurate to me and should I think keep everyone happy. The radiator detail looks a little on the weak side to me, but you can’t have everything. The odd part here is that in order to display any of the engine detail surgery will be needed on the nacelles as they have not been designed for display of the area with the exception of the side panels.

ICM has supplied both the FuG 202 and FuG 220 Radar antenna which is a nice option; if you are not happy with the antenna offered then I believe Master offer brass options for you.

ICM has provided four finishing options for this model with two options for both sets of radar. The decals themselves are glossy with good colour register and are also very thin; running a finger over the decal sheet I cannot detect the edges of the decals with my fingers. The finishing options are:
Ju 88C-6B, Pilot Lt Wilhelm Beier, 10/NJG 1, October 1942
Ju 88C-6B, Pilot Maj Heinrich Prinz zu Sayn-Wittgenstein, Stab IV/NJG 5, Orel Russia, Spring 1943
Junkers 88C-6b, 3/NJG 4, Mainz, March 1944
Junkers 88C-6b, 6/NJG 2, Kassel, Spring 1944

Conclusion

If you are a fan of German aircraft and you want a model that can be built from the box with a small amount of added detail by the modeller that results in a nice offering; then this model is well worth you looking into. The cockpit area is nicely busy that a small amount of work will lift to a high standard. Construction all appears straight forward and been tackled in a very promising way. The detail of the parts is very nice for the most part and of course there are aftermarket options for those who want to take it further. the downsides for me are the lack of Swastikas on the tail that I feel could be tackled in a sensitive way for those that may be offended. The distortion of the engine nacelles is a disappointment to me.

SUMMARY
Darren Baker takes a look at the Ju 88C-6b WW2 German Night Fighter from ICM in 1/48th scale.
  Scale: 1:48
  Mfg. ID: 48239
  PUBLISHED: Dec 16, 2018
  NATIONALITY: Germany
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 87.04%
  MAKER/PUBLISHER: 84.86%

Our Thanks to ICM Holding!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View Vendor Homepage  |  More Reviews  

About Darren Baker (CMOT)
FROM: ENGLAND - SOUTH WEST, UNITED KINGDOM

I have been building model kits since the early 70’s starting with Airfix kits of mostly aircraft, then progressing to the point I am at now building predominantly armour kits from all countries and time periods. Living in the middle of Salisbury plain since the 70’s, I have had lots of opportunitie...

Copyright ©2021 text by Darren Baker [ CMOT ]. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of AeroScale. All rights reserved.



Comments

Darren, Thanks for the review. This one is on my Christmas wish list, so I'm going the cowling problem isn't universal. Gaz
DEC 16, 2018 - 03:57 PM
It is an issue I have found before and is due to packing everything in one bag. So it really is a case of 50/50.
DEC 16, 2018 - 07:05 PM
Hi Darren I think these reviews really do need a test-fit, because the difference I've found between the early and more recent mouldings is like the proverbial chalk and cheese - shockingly different. I've actually not gone ahead with a couple of reviews because they were so far off my initial take on the '88 that I began to question whether I'd simply received a dud. All the best Rowan
DEC 18, 2018 - 09:02 AM
I do not have the time now I am doing two full time jobs to provide build reviews in anything like a timely manner and so I get the in box review done in order that the item is not stale and the provider is happy.
DEC 18, 2018 - 12:30 PM
Hi Darren I fully understand the pressures and sympathise with you (try running an Oxfam shop and putting in double the hours you're paid for - so I know where you're coming from ) - but you state in the review that "Construction all appears straight forward" when the moulding problems with ICM's Ju 88s have been evident for some time and the review photos honestly don't look encouraging. It would definitely be worth spending an extra 15 mins in a case like this because, if the nacelles etc. all lined up properly again, it would be important news and would encourage modellers to have renewed faith in a kit series that many are understandably shying away from. That alone would be the core reason to buy the kit (or not) for many modellers. For me it's a crying shame that a great kit of such an important aircraft went off the rails somewhere because of production problems. Whether it's down to a change in styrene (the colour has changed compared with the early kits), or simply not allowing the sprues sufficient time to cool, ICM really do need to nail this issue. All the best Rowan
DEC 19, 2018 - 09:57 AM
I have made two of their Ju 88's and met no issues and so I am stumped as to why they were troublesome. If I get time I will have a play with the major parts of this one.
DEC 19, 2018 - 10:36 AM
Maybe you guys need to find some people who aren't working two jobs or running his own business to do some reviews.
DEC 20, 2018 - 08:18 PM
Hi Gary Sorry for the late reply (work, you know... ) - but, seriously, we've always sought to get as many new reviewers on board as we can. When I was in charge, the only pre-requisite that I set was to demonstrate a willingness and ability to meet Aeroscale's standards by contributing a few reviews of items before requesting any samples. I've already passed on the vast majority of the contacts I've made over the years to others, so I don't receive things often these days. I know Darren makes plenty of samples available, so he doesn't really deserve a dig. If you fancy reviewing some stuff in any genre, just check the sample lists for each Kitmaker site - I can see at a glance that there's some interesting stuff on the Aeroscale section that Kevin's added: https://docs.google.com/spreadsheets/d/1nTzqFHkdJretXNguGngdsK4ZL4y0fwdMOfLRk_FDpHI/edit#gid=11 All the best Rowan
DEC 24, 2018 - 10:32 AM
   
ADVERTISEMENT


Photos
Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
ADVERTISEMENT